![]() |
my profile |
register |
faq |
search upload photo | donate | calendar |
|
|
|
|
#1 |
|
User
Join Date: Feb 2010
Location: Tennessee
Posts: 1,149
Thanks: 159
Thanked 664 Times in 318 Posts
|
Rich,
I made a receiver insert today, and after some measuring and test fitting I found that .540" x .540 was a snug fit. I figured that the firing pin is most likely centered, so I drilled a hole and chucked it up in the lathe (barrel band in the 3-jaw chuck and with a live center in the insert). With an indicator at the rear end of the taper (right before it rounds over), I read a .006" TIR side to side. Top to bottom was only .002" TIR, which is not too bad considering that the barrel has some slight pitting. I turned the insert 180 degrees and tried again, and got the same result. The low reading was on the same side regardless of how I turned the insert, so it seems like the bore for the bolt is off center. The point I measured is about 1/3 from the muzzle, which means that the rear of the receiver is off by .009". Have you tried to measure the runout on an intact barrel/receiver, or do you know what a normal runout would be? |
|
|
|
|
|
#2 | |
|
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
|
Quote:
Here's my setup - the first pic is some of my ground drill rod blanks that I use for bore measuring...And by clamping my 7.6mm rod in the chuck and turning the C96 barrel extansion (not the chuck) by hand, I got the indicated runouts... When I was done with that, I chucked my C96 barrel extension between a center in the chuck and my brass insert and got exactly the same results...Yeah, I was surprised too...
__________________
I like my coffee the way I like my women... ...Cold and bitter...
Last edited by sheepherder; 11-10-2014 at 08:49 PM. |
|
|
|
|
|
|
#3 |
|
User
Join Date: Feb 2010
Location: Tennessee
Posts: 1,149
Thanks: 159
Thanked 664 Times in 318 Posts
|
Rich,
I tried the setup in your third pic, but with a turned brass rod instead of a straight rod. I got the same side-to-side runout as when chucking it by the barrel band, but the up/down runout was now about .015. Seems like the bore is off center by maybe .007-.008 at the muzzle. Anyway, the runout in your second picture is close to what I got in the very same location, so I guess these guns are not as precisely machined as I thought they were. That could make it iffy to get a new barrel centered, as you won't have any reliable index points. On the other hand: It won't be difficult to stay within Mauser's tolerances, a tape measure will probably do just fine...
|
|
|
|
|
|
#4 |
|
User
Join Date: Feb 2010
Location: Tennessee
Posts: 1,149
Thanks: 159
Thanked 664 Times in 318 Posts
|
BTW: For operations like this, I prefer to turn a rod and leave it chucked until I'm done. My Emco 3-jaw chucks usually stays within .001" TIR, but turning the rod right there and then will eliminate any possible runout caused by the chuck. I use a brass rod, and turn about 1/4" to a diameter that slips into the bore. Then I back off .001", turn another 1/8", back off etc so I get a stepped taper. This will usually get me dead center in the bore.
|
|
|
|
|
|
#5 | |
|
Lifer
Lifetime Forum Patron Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
|
Quote:
tell you what - that barreled extension up in the last post is an original C96 Mauser. Bore is a bit worn, but good rifling. Let me get my last re-barrel out and measure the runout on that...Stay tuned... Ooowww...I'm not as good as the boyz at Mauserwerke...
__________________
I like my coffee the way I like my women... ...Cold and bitter...
Last edited by sheepherder; 11-10-2014 at 11:08 PM. |
|
|
|
|
![]() |
| Tags |
| blivet |
| Thread Tools | |
| Display Modes | |
|
|