LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Shooting and Reloading

Reply
 
Thread Tools Display Modes
Unread 07-20-2013, 06:50 PM   #1
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,316
Thanks: 2,768
Thanked 1,000 Times in 735 Posts
Default

You didn't get hosed, as that is how Lee sells them. The 30 Luger and the 30 Mauser both take the .308-.309 bullet . Check out the interior of your Lee sizing die for mirror smoothness. I purchased a set of lee 30 Luger dies, and the sizing die was totally unusable due to poor finish(it looked like it had been finished with a rat tailed file).

On the 30 luger round, neck tension is critical to avoid bullet set back when the bullet goes up the feed ramp. You want .003-.005 in. of fit interface between you case neck ID and your bullet OD. Use a minimal crimp if you are using a taper crimp(which is what your Lee dies does) The LFCD applies a collet crimp, which is what I am currently using. I plan to put cannalures on a batch of FMJ bullets, and see if that helps protect against setback when loading .308 bullets.

I have loaded .308 in dia bullets with success in 30 Luger brass. Hornady makes a .309 dia. XTP HP bullet, and Natchez Shooting has them in stock currently. I have also had good luck with western Bullets LRN in .310 dia..

Look at the thread just below this one and a search will get you more information.

Last edited by rhuff; 07-20-2013 at 06:51 PM. Reason: To add info.
rhuff is offline   Reply With Quote
The following 2 members says Thank You to rhuff for your post:
Unread 07-20-2013, 07:43 PM   #2
cneider
User
 
Join Date: Jul 2003
Location: Phoenix, AZ
Posts: 59
Thanks: 28
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by rhuff View Post
You didn't get hosed, as that is how Lee sells them. The 30 Luger and the 30 Mauser both take the .308-.309 bullet . Check out the interior of your Lee sizing die for mirror smoothness. I purchased a set of lee 30 Luger dies, and the sizing die was totally unusable due to poor finish(it looked like it had been finished with a rat tailed file).

I have loaded .308 in dia bullets with success in 30 Luger brass. Hornady makes a .309 dia. XTP HP bullet, and Natchez Shooting has them in stock currently. I have also had good luck with western Bullets LRN in .310 dia..

Look at the thread just below this one and a search will get you more information.
Thanks for responding. I checked the sizing die and see what you mean. It's not a mirror finish-there are some machining marks. I've read that about Lee dies before. It didn't seem to affect the one case I ran through it before I tested the expander die. If it DID become a problem, I'm wondering if I could polish it out with a Dremel felt bit and some rouge?

How are those hollow points feeding for you in your Luger? I've always been leery about reloading anything except ball ammunition for my automatics ever since I loaded a batch of 9mm hollow points and flat points for my Walther P38 in 1975. Feeding problems-they kept hanging up on the feed ramp when I fired them, although they seemed to feed just fine when I hand cycled them. I wasn't adventurous enough to take me Dremel to the feed ramp on my commercial P38.
cneider is offline   Reply With Quote
Unread 07-20-2013, 07:58 PM   #3
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Quote:
Originally Posted by rhuff View Post
I plan to put cannalures on a batch of FMJ bullets...
I'm curious as to how you will do that...I've never done it (or even thought about doing it), but it sounds interesting...

I have had disastrous results with Lee dies back in the day; I use only RCBS now...30 Luger shows up on eBay occasionally; it is worth the wait and $$$ to get them...
__________________
I like my coffee the
way I like my women...
...Cold and bitter...
sheepherder is offline   Reply With Quote
Unread 07-21-2013, 09:04 PM   #4
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,316
Thanks: 2,768
Thanked 1,000 Times in 735 Posts
Default

Quote:
Originally Posted by postino View Post
I'm curious as to how you will do that...I've never done it (or even thought about doing it), but it sounds interesting... :


I purchased a cannalure tool from C-H Tool Co. a number of years ago. It is basically a knurling tool for bullets(jacketed and plated, but not lead). I have used it frequently on bullets that I wanted to load for a revolver, and they had no cannalure......so I put one on them. If you look closely at the Fiocchi and Winchester 30 Luger ammo, the bullets have a cannalure and a mild roll crimp. The original 30 Luger rounds also(I am pretty sure) have the same setup. It stops the tendency for setback due to such a short case neck(not a lot of neck tension) on the 30 Luger brass.
rhuff is offline   Reply With Quote
Unread 07-21-2013, 11:21 PM   #5
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Quote:
Originally Posted by rhuff View Post
The original 30 Luger rounds also(I am pretty sure) have the same setup. It stops the tendency for setback due to such a short case neck(not a lot of neck tension) on the 30 Luger brass.
30 Luger Fiocchi [93gr] does have the cannelure; PRVI [7.62 Tok] does not [85gr]. Peters 30 Luger [93gr] does; Winchester 30 Luger [93gr] does.

I have two rounds of DWM K K 471 original 7.65 Parabellum; they do not have a cannelure (don't know what grain).

The Tokarev brass I included because the case neck is shorter than the 30 Luger (.125" vs .155"), yet PRVI does not use a cannelured bullet.

Interesting...

I will add the C-H Cannelure tool to my 'want list'. I can't find my old collet crimping tool either. Another addition to the 'want list'.

Edit: Does that CH tool have a part number on it???
__________________
I like my coffee the
way I like my women...
...Cold and bitter...
sheepherder is offline   Reply With Quote
Unread 07-22-2013, 04:49 PM   #6
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,316
Thanks: 2,768
Thanked 1,000 Times in 735 Posts
Default

Quote:
Originally Posted by postino View Post

Edit: Does that CH tool have a part number on it???



Here you go:

C-H Tool & Die/4-D Custom Die Co.
P.O. Box 889
Mt. Vernon, Oh 43050
740-397-7214 740-397-6600


Tool #12000


They have a website also. Go spend some money, it will make you feel good!!


The automated cannalure tools cost about $600 the last time I looked, but this one is very reasonably priced. It fit my budget much better.
rhuff is offline   Reply With Quote
The following member says Thank You to rhuff for your post:
Unread 07-22-2013, 07:29 PM   #7
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Quote:
Originally Posted by rhuff View Post
They have a website also. Go spend some money, it will make you feel good!!
C-H Tool & Die/4-D Custom Die Co.
P.O. Box 889
Mt. Vernon, Oh 43050
740-397-7214 740-397-6600

Tool #12000

Here we go...

http://www.ch4d.com/equipment/bullet-tools/CanToo



Cost is $95...And they are - "New orders are currently taking about 2 to 3 weeks to process and ship"...

Their price for the 2-die 30 Luger reloading die set is reasonable as well - $80...
__________________
I like my coffee the
way I like my women...
...Cold and bitter...

Last edited by sheepherder; 07-22-2013 at 11:10 PM.
sheepherder is offline   Reply With Quote
Unread 07-22-2013, 07:53 PM   #8
cneider
User
 
Join Date: Jul 2003
Location: Phoenix, AZ
Posts: 59
Thanks: 28
Thanked 1 Time in 1 Post
Default

Quote:
Originally Posted by postino View Post
C-H Tool & Die/4-D Custom Die Co.
P.O. Box 889
Mt. Vernon, Oh 43050
740-397-7214 740-397-6600

Tool #12000
Here we go...

http://www.ch4d.com/equipment/bullet-tools/CanToo



Cost is $95...And they are - "New orders are currently taking about 2 to 3 weeks to process and ship"...

Bookmarked! What a handy little gadget for the reloading bench!

Their price for the 2-die 30 Luger reloading die set is reasonable as well - $80...[/QUOTE]
cneider is offline   Reply With Quote
Unread 07-23-2013, 06:38 PM   #9
rhuff
Patron
LugerForum
Patron
 
rhuff's Avatar
 
Join Date: Mar 2011
Location: Az.
Posts: 2,316
Thanks: 2,768
Thanked 1,000 Times in 735 Posts
Default

Quote:
Originally Posted by postino View Post
C-H Tool & Die/4-D Custom Die Co.
P.O. Box 889
Mt. Vernon, Oh 43050
740-397-7214 740-397-6600

Tool #12000

Here we go...

http://www.ch4d.com/equipment/bullet-tools/CanToo



Cost is $95...And they are - "New orders are currently taking about 2 to 3 weeks to process and ship"... .


WOW!! They had really gone up in price. I believe that I paid $49 for mine....granted, that was a few years ago. They work very well (simple, and I need that) and once it is set, one can turn out some cannalured bullets. They are nicely made and not a cheap piece of crap.
rhuff is offline   Reply With Quote
Unread 07-21-2013, 08:56 AM   #10
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Quote:
Originally Posted by rhuff View Post
The LFCD applies a collet crimp, which is what I am currently using.
I'm don't recognize "LFCD"...What/who is it???

I have used a collet crimper in the past; don't recall who made it...On my 357 AMP cartridges, I think (it was decades ago)...I really couldn't get enough pressure using my RockChucker press to get a good collet/case mouth crimp...It was a 3-prong/finger crimping die...You still had to taper crimp it first, IIRC...The collet crimp was an extra operation...

I should probably try it again...I'm sure they've improved it by now...So that even a dummy like me could get a good case mouth crimp...
__________________
I like my coffee the
way I like my women...
...Cold and bitter...
sheepherder is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:23 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com