Glue for Rifle Stock Repair???

[Olle]

By the way, here's an SMLE I fixed up a while back. The buttstock was the older, dark walnut and the forearm was a newer replacement made of some kind of lighter wood (possibly beech). It took a few attempts and a lot of bad language, but it matched quite nicely once I was done with it.

[sheepherder]

Originally Posted by Olle

By the way, here's an SMLE I fixed up a while back. The buttstock was the older, dark walnut and the forearm was a newer replacement made of some kind of lighter wood (possibly beech). It took a few attempts and a lot of bad language, but it matched quite nicely once I was done with it.

Excellent!!!

I did a couple bubba-ized No 1 SMLE's as faux 'jungle carbines' using Redfield #75 peep sights w/hunting knobs and Numrich flash hiders and rubber & steel buttplates...And one #4 'jungle carbine' also...Pics around here someplace...I also have two boxes of parts for #1 and #4 rifles, plus about eight different buttstocks...

Sadly, both stock disks I have are blanks; no regimental markings...

[sheepherder]

I put it all back together, to get an idea of what it would look like, compared to what it was and what an 1891 cavalry carbine should look like...

(Top to Bottom: 1891 Argentine rifle, bubba sporter, 1891 Argentine cavalry carbine, my faux carbine)

[Olle]

Originally Posted by postino

Sadly, both stock disks I have are blanks; no regimental markings...

Those discs can be found on eBay, but they're getting kinda pricey. My project was on a shoestring budget, so I simply turned a brass disc and aged it a bit by scratching and dinging it, then wiping it with Blacken-It ( http://www.micromark.com/blacken-it-4-fl-oz,7267.html ). It turned out nicely, but it would have looked much better with the markings.

[sheepherder]

Originally Posted by Olle

Those discs can be found on eBay, but they're getting kinda pricey. My project was on a shoestring budget, so I simply turned a brass disc and aged it a bit by scratching and dinging it, then wiping it with Blacken-It ( http://www.micromark.com/blacken-it-4-fl-oz,7267.html ). It turned out nicely, but it would have looked much better with the markings.

I've seen pics of regimental marked disks on SurplusRifle Forum, but have no idea what regiments they belong to, or if there was a standard for the marks [letters/numbers/slashes]...I have one steel & one brass...

For my fake carbines, I fill the disk hole in with a wood plug, since part of it gets milled out anyway for the sling relief...

[sheepherder]

I'm doing another 1891 Argentine Mauser stock extension, to make another bubba-ized rifle into a carbine w/full-length stock; this time I milled a 1/2" wide x 3/8" high x 6" long slot in the combined bubba-ized stock & extension...Then I milled a same size Walnut 'plug' and glued it in place...I rough sanded it down...

It looks like a butt-splice, but it's actually a hidden tongue & groove splice.

When I first started, both the stock and extension looked the same color...(I had seven Mauser/Steyr/Enfield stocks to choose the extension from)...I chose an Enfield No 4 stock for the extension...The color looked close...

After sanding, the colors no longer match...

No matter. The barrel cap, front sight band & blade, and rear band/sling swivel are en route.

[sheepherder]

Originally Posted by Olle

Those discs can be found on eBay...I simply turned a brass disc...

Here's a disk that came on the Swedish M96 stock I got off ebay...Don't have the slighest idea what it means, but it looks cool...Someone put a little bit of effort into the markings...

Edit: I found a site that deciphers the Swedish markings...Sort of...

http://www.gotavapen.se/gota/artikla..._se_rifles.htm

[Olle]

That disc seems to be buggered up. The "1, 2, 3" sector shows the barrel wear, and there should only be one mark. The "2-5" and "9-1" show the actual gore gauge, but it should also only have one mark.