LugerForum Discussion Forums my profile | register | faq | search
upload photo | donate | calendar

Go Back   LugerForum Discussion Forums > General Discussion Forums > Repairs, Restoration & Refinishing

Reply
 
Thread Tools Display Modes
Old 04-23-2013, 12:01 AM   #1
Olle
User
 
Olle's Avatar
 
Join Date: Feb 2010
Location: Tennessee
Posts: 1,149
Thanks: 159
Thanked 664 Times in 318 Posts
Default

Quote:
Originally Posted by postino View Post
...Until you try to put the toggle axle pin in...It's pretty much a precise fit...

Part of the problem with 'spreading' the sides is that both sides want to spread at the same time whether you support them or not...I toyed with the idea of making a special mandrel to insert into the receiver, with a drilled & aligned hole for a 8.82mm rod that would enter the barrel...Then you could work on 'spreading' the sides one at a time...

I do have a brass receiver insert for my barrel swaps; in an emergency (which is doubtful in my future) I could drill it and insert a squib rod to make a shade-tree fixture...But that axle pin is the most oddball size ever designed; not Metric and not Yankee...Not Inch, not Letter size, not Number size...You'd have to make up a special pin (or use a spare axle pin) to test your alignment after every tweak...

...Or just box it up and send it to Gerry!!!
I was thinking about supporting and clamping the barrel, instead of using a rod in the bore. If you lay it flat on its side and clamp it both at the muzzle end and right at the chamber, you would only be bending one rail... or?

But yeah, boxing it up and sending it to Gerry sounds like a safer alternative.
Olle is offline   Reply With Quote
Old 04-23-2013, 09:56 AM   #2
sheepherder
Lifer
Lifetime Forum
Patron
 
sheepherder's Avatar
 
Join Date: Feb 2009
Location: ...on the 'ol Erie Canal...
Posts: 8,208
Thanks: 1,425
Thanked 4,474 Times in 2,343 Posts
Default

Quote:
Originally Posted by Olle View Post
I was thinking about supporting and clamping the barrel, instead of using a rod in the bore. If you lay it flat on its side and clamp it both at the muzzle end and right at the chamber, you would only be bending one rail...
Just out of curiosity, where do you intend to apply pressure on the rail to bend it???

BTW, is there an amusing story behind how this rail got bent???

(Mine got bent when I removed the barrel without proper tools)...
__________________
I like my coffee the
way I like my women...
...Cold and bitter...
sheepherder is offline   Reply With Quote
Old 04-23-2013, 10:54 AM   #3
Olle
User
 
Olle's Avatar
 
Join Date: Feb 2010
Location: Tennessee
Posts: 1,149
Thanks: 159
Thanked 664 Times in 318 Posts
Default

Quote:
Originally Posted by postino View Post
Just out of curiosity, where do you intend to apply pressure on the rail to bend it???

BTW, is there an amusing story behind how this rail got bent???

(Mine got bent when I removed the barrel without proper tools)...
My approach would be to lay it with the left side down on a fixture (for example, a heavy aluminum block) and clamp the barrel, the chamber and the left rail securely. This would leave the right rail unsupported. Then I would insert a machinist's jack between the rails and push, while reading with a dial indicator at the end of the rail. I can make a spacer block (using another Luger to get the correct dimension) to get a fairly accurate base reading for the indicator, then I'd push beyond that a bit.

After doing this in increments a few times, I should get a pretty good idea of the springback. After the final push, it should spring back to the base reading. I'm sure there will be some fine tuning after that, but this should get it back within reasonable tolerances. Well, that's what I had envisioned anyway.

It was bent when I got it so I really don't know what happened to it, but it takes a lot of force to get a breech block in between the rails so somebody must have squeezed it pretty darn good. There are some bad diagonal gouges on the rails, almost like the extension has "derailed" at some point, and I'm sure that this has something to do with it. I might even take it to a machine shop to have it crack tested before I go any further, I definitely don't want it to break.
Olle is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:22 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2026, Lugerforum.com