Round not consistently extracting

mestguy182 · 10-06-2018, 12:25 AM

Thank you for the replies. I'm using 115 GR Winchester White Box, 9mm. I did replace the extractor spring, I held on to the old one and may test putting it back in.

However, I found an issue I missed before, the ejector I changed out was not an original part and I noticed after my first post that the slide was feeling very notchy. It turns out that the ejector was too tall and was rubbing up against the frame. I filed the ejector down and now the slide moves smoothly. Could this have caused my issue?

4 Scale · 10-06-2018, 10:03 AM

Quote:

Originally Posted by mestguy182

Could this have caused my issue?

I have never dealt with this particular issue but from my understanding of Lugers I would say possibly. As David points out, it is important to fix and then test one element at a time.

DonVoigt · 10-06-2018, 11:43 PM

Quote:

Originally Posted by mestguy182

Thank you for the replies. I'm using 115 GR Winchester White Box, 9mm. I did replace the extractor spring, I held on to the old one and may test putting it back in.

However, I found an issue I missed before, the ejector I changed out was not an original part and I noticed after my first post that the slide was feeling very notchy. It turns out that the ejector was too tall and was rubbing up against the frame. I filed the ejector down and now the slide moves smoothly. Could this have caused my issue?

For sure.

You are sometimes mixing up extractor and ejector, and it gets confusing; I'm assuming you mean extractor.
The ejector is the long spring in the side of the receiver extension, and does not have a "spring" it is its own spring.

rhuff · 10-07-2018, 02:41 PM

Quote:

Originally Posted by DonVoigt

For sure.

You are sometimes mixing up extractor and ejector, and it gets confusing; I'm assuming you mean extractor.

I wondered if it was only me that was getting confused about this thread's terminology(It is getting much easier these days to confuse me).

kurusu · 10-07-2018, 05:03 PM

OK. Let's get this thing done.

Extractor. A numbered part uses a spring for tension.

802.jpg

Ejector. Not numbered, it is a spring in itself.

839.jpg

This started wrong when the OP wrote he replaced the "ejector" spring. That thing doesn't exist. So I assume he meant "extractor" spring.

Later he wrote the ejector broke. And here I believe he really meant it. Ejectors break quite often.

10-07-2018, 05:03 PM	#5
kurusu User Join Date: Sep 2007 Posts: 1,225 Thanks: 2,679 Thanked 930 Times in 509 Posts	OK. Let's get this thing done. Extractor. A numbered part uses a spring for tension. 802.jpg Ejector. Not numbered, it is a spring in itself. 839.jpg This started wrong when the OP wrote he replaced the "ejector" spring. That thing doesn't exist. So I assume he meant "extractor" spring. Later he wrote the ejector broke. And here I believe he really meant it. Ejectors break quite often. Last edited by kurusu; 10-07-2018 at 06:32 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-06-2018, 12:25 AM	#1
mestguy182 User Join Date: Sep 2018 Location: Indialantic, FL Posts: 26 Thanks: 15 Thanked 2 Times in 1 Post	Thank you for the replies. I'm using 115 GR Winchester White Box, 9mm. I did replace the extractor spring, I held on to the old one and may test putting it back in. However, I found an issue I missed before, the ejector I changed out was not an original part and I noticed after my first post that the slide was feeling very notchy. It turns out that the ejector was too tall and was rubbing up against the frame. I filed the ejector down and now the slide moves smoothly. Could this have caused my issue?