"When opportunity knocks!!!"

DonVoigt · 03-22-2017, 11:16 AM

GT,
You will "never" get a consensus on this, so just pick what You want and go with it!

G.T. · 03-22-2017, 03:11 PM

Hi Don, yes, I think you are correct!.... I was hoping for a little more tried and true measurements.... but, we will press on... Thanks and best to all, til....lat'r......GT...

G.T. · 04-04-2017, 10:36 PM

I have requested 5 different heights, starting with standard, at approx. .200" the going up in the following heights, .225", .250", .275", .300"..... If push come to shove... it will be .200", .250", .300" that's if I have any choices at all when the numbers come back... I'm trying.. just don't know if the horse I'm riding has long enough legs!....

....best to all, til...lat'r...GT...

G.T. · 04-11-2017, 06:19 PM

I'm not too good at explaining what I'm after on the sight height equation... but lets start from the very beginning! And it starts like this! I can't see worth a damn, never have had good eyesight, and I think I was absent or in the can when they were handing out good eyesight, because I missed it... by a long way? But, I still like to hear the gun go bang and the dust jump up and the target run away... most likely 100% of the time... So, when I look at a Luger sight picture... I see all kinds of fuzzy lines and dots and fuzzy targets as well.... just like described above, the sight height means little or nothing to me, OTHER, than, I realize there are those who can see.. and every little increment of height actually make a difference to them, and the target! So, if you put the top of the front sight blade, lined up straight with the top of the rear sight, and hold the point dead center at approx. 25 yards.... Is that where your luger shoots... ??.. Don't care about left and right, just up and down... If your luger shoots anywhere close to center, then I would like to know the height of the front sight blade from the top of the sight block, to the top of the blade... It will probably be anywhere from .200" to .218" ... but I would like to know if it shoots to point of aim with that height?.... Let me know, as I have finalized an order for couple of 100 units of different heights, and I'd really like some more feedback from you shooter guys to finalize the different quantities...

... best to all, til...lat'r....GT

03-22-2017, 11:16 AM	#1
DonVoigt User Join Date: Apr 2015 Location: near Charlotte NC Posts: 4,683 Thanks: 1,443 Thanked 4,358 Times in 2,042 Posts	GT, You will "never" get a consensus on this, so just pick what You want and go with it! __________________ 03man(Don Voigt); Luger student and collector. Looking for DWM side plate: 69 ; Dreyse 1907 pistol K.S. Gendarmerie

03-22-2017, 03:11 PM	#2
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,550 Thanks: 1,361 Thanked 3,778 Times in 1,028 Posts	sights! Hi Don, yes, I think you are correct!.... I was hoping for a little more tried and true measurements.... but, we will press on... Thanks and best to all, til....lat'r......GT...

04-04-2017, 10:36 PM	#3
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,550 Thanks: 1,361 Thanked 3,778 Times in 1,028 Posts	here's what's on the plate! I have requested 5 different heights, starting with standard, at approx. .200" the going up in the following heights, .225", .250", .275", .300"..... If push come to shove... it will be .200", .250", .300" that's if I have any choices at all when the numbers come back... I'm trying.. just don't know if the horse I'm riding has long enough legs!........best to all, til...lat'r...GT...

04-11-2017, 06:19 PM	#4
G.T. Lifer Lifetime Forum Patron Join Date: Jun 2002 Location: Chandler Arizona Posts: 3,550 Thanks: 1,361 Thanked 3,778 Times in 1,028 Posts	Ok, let's try this a different way! I'm not too good at explaining what I'm after on the sight height equation... but lets start from the very beginning! And it starts like this! I can't see worth a damn, never have had good eyesight, and I think I was absent or in the can when they were handing out good eyesight, because I missed it... by a long way? But, I still like to hear the gun go bang and the dust jump up and the target run away... most likely 100% of the time... So, when I look at a Luger sight picture... I see all kinds of fuzzy lines and dots and fuzzy targets as well.... just like described above, the sight height means little or nothing to me, OTHER, than, I realize there are those who can see.. and every little increment of height actually make a difference to them, and the target! So, if you put the top of the front sight blade, lined up straight with the top of the rear sight, and hold the point dead center at approx. 25 yards.... Is that where your luger shoots... ??.. Don't care about left and right, just up and down... If your luger shoots anywhere close to center, then I would like to know the height of the front sight blade from the top of the sight block, to the top of the blade... It will probably be anywhere from .200" to .218" ... but I would like to know if it shoots to point of aim with that height?.... Let me know, as I have finalized an order for couple of 100 units of different heights, and I'd really like some more feedback from you shooter guys to finalize the different quantities... ... best to all, til...lat'r....GT

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode